SECTION
13411
INSTRUMENT
CONSOLES
PART
1 GENERAL
1.1 SECTION INCLUDES
A. Instrument consoles.
1.2 RELATED SECTIONS
1.3 REFERENCES
A. ASTM D 638 - Standard Test Method
for Tensile Properties of Plastics.
B. ASTM D 790 - Standard Test Methods
for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical
Insulating Materials.
1.4 SUBMITTALS
A. Submit under provisions of Section
01300.
B. Product Data: Test results of fiberglass reinforced
plastic laminate.
C. Shop Drawings: Show:
1.
Critical
dimensions, jointing and connections, fasteners and anchors.
2.
Materials
of construction.
3.
Sizes,
spacing, and locations of structural members, connections, attachments,
openings, fasteners, and loads.
D. Manufacturer's installation
instructions.
1.5 DELIVERY, STORAGE, AND HANDLING
A. Store products indoors and protect
from construction traffic and damage.
PART
2 PRODUCTS
2.1 MANUFACTURER
A. Provide products manufactured by
Warminster Fiberglass Company; P.O Box 188, Southampton PA 18966-0188; ASD.
Tel. (215) 953-1260, Fax. (215) 357-7893. www.warminsterfiberglass.com
B. Requests for substitution will be
considered in accordance with provisions of Section 01600.
C. Substitutions: Not permitted.
2.2 INSTRUMENT CONSOLES
A. Fiberglass Material:
1.
Tensile
strength (ASTM D 638): 9,000 psi.
2.
Flexural
strength (ASTM D 790): 15,000 psi.
3.
Flexural
modulus (ASTM D 790): 900,000 psi.
B. Construction: Totally enclosed molded fiberglass
reinforced plastic instrument panels.
1.
One-piece
molded construction. No metal strips
required to form mechanical joints.
2.
Smooth
satin, gel-coated outside surfaces; no exposed glass fibers.
3.
1/2
inch radius rounded corners; cutout edges sanded and smooth.
4.
Recessed,
lift-off access doors with Southco Type 44 latches.
5.
Nominal
wall thickness, instrument mounting surface:
1/4 inch.
6.
Nominal
wall thickness, elsewhere: 1/8 inch.
7.
Access
doors: Front and rear.
8.
Open
bottom construction; 2-1/2 inch mounting flange and factory drilled anchor
holes.
9.
Color: Beige, or as required.
10.
Color: _______________.
11.
Table-top
type, 36 inches wide: Model WFC1010BB.
12.
Table-top
type, 48 inches wide: Model WFC1015BB.
13.
Table-top
type, 66 inches wide: Model WFC1020BB.
14.
Low
breakfront type, 36 inches wide: Model
WFC1010CB.
15.
Low
breakfront type, 48 inches wide: Model
WFC1015CB.
16.
Low
breakfront type, 66 inches wide: Model
WFC1020CB.
17.
High
breakfront type, 36 inches wide: Model
WFC1010DB.
18.
High
breakfront type, 48 inches wide: Model
WFC1015DB.
19.
High
breakfront type, 66 inches wide:
WFC1020DB.
20.
Surface
finish: Matte.
21.
Surface
finish: Satin.
22.
Gasket
on doors.
23.
Galvanized
power struts.
24.
Fiberglass
power struts.
25.
Instrument
cut-outs.
26.
1/4
inch thick fiberglass sub-panel, mounted on power struts.
27.
1/8
inch thick steel sub-panel, mounted on power struts.
PART
3 EXECUTION
3.1 EXAMINATION
A. Verify that dimensions are correct
and project conditions are suitable for installation. Do not proceed with installation until unsatisfactory conditions
have been corrected.
3.2 INSTALLATION
A. Install products in accordance with
manufacturer's instructions.
B. Ensure that products are installed
plumb and true, free of warp or twist, within tolerances specified by the
manufacturer and as indicated in the contract documents.
C. Anchor consoles to floor with
expansion anchors.
3.3 ADJUST AND CLEAN
A. Clean surfaces in accordance with
manufacturer's instructions.
B. Remove trash and debris, and leave
the site in a clean condition.
END OF SECTION